#######################
## [2.0.12] - 04/03/2022
### Updated
- Recovery-2.1-2
- system-update-utilities


#######################
## [2.0.11] - 18/02/2022
### Added
- NGPS 300-18 model; updated params of NGPS 300-36 and 400-25

### Updated
- Recovery-2.1.0
- Oscilloscope 
- EULA
- system-update-utilities

### Fixed
- Fixed parallel bug (issue present only in ver 2.0.9 and 2.0.10)


#######################
## [2.0.10] - 24/11/2021
### Fixed
- NGPS 200-60 max power
- PID limiter (issue present only in ver 2.0.9)


#######################
## [2.0.9] - 19/10/2021
### Added
- NGPS 150-70, 200-60;
- Auto tuning.
- New recovery image 2.0.4 with updated system update server

### Updated
- FAST-PS 0540 psm;
- UPDT format;
- Update server to support new UPDT format.

### Fixed
- Trigger type from web interface;
- Crowbar reset when in test and calibration section.


#######################
## [2.0.8] - 18/03/2021
### Fixed
- Reset of interlock.


#######################
## [2.0.7] - 18/03/2021
### Added
- Internal status IV register.


#######################
## [2.0.6] - 25/02/2021
### Added
- Modbus update mode, regulation mode, over current, over voltage, temperature and set voltage.

### Fixed
- NGPS 1000-10 gain;
- TRIG capability for FAST-PS calibration.


#######################
## [2.0.5] - 18/12/2020
### Added
- NGPS 100-150, 125-120, 300-30, 170-60, 105-100.

### Fixed
- Dissipative fault in case of the parallel mode.


#######################
## [2.0.4] - 01/12/2020
### Fixed
- Slew rate at startup;
- Web interface interlocks test black screen.


#######################
## [2.0.3] - 26/11/2020
### Added
- OCEM serial and part number (RESERVED);
- Insulation test for NGPS (RESERVED);
- recovery 2.0.2;
- Swap file.

### Fixed
- AIN, trigger and DDCT default test status (RESERVED);
- lcd-ctrl crash when NETWORK tab is selected;
- lcd-ctrl initial focus in NETWORK tab;
- lcd-ctrl black screen at startup when the ethernet network cable is disconnected and DHCP mode is selected;
- Full clean up during firmware upgrade;
- nodejs crash when web interface is used to upgrade the firmware;
- Slew rate ramp resolution.


#######################
## [recovery 2.0.2] - 18/11/2020
### Fixed
- Full clean up during firmware upgrade.


#######################
## [2.0.2] - 09/11/2020
### Changed
- Finalize model is not destroyed when a new psm is selected (RESERVED).

### Updated
- NGPSs' psm (RESERVED).


#######################
## [2.0.1] - 22/10/2020
### Updated
- SFP:LAST_CMD command.

### Fixed
- Dissipative fault for the slaves in case of the parallel mode;
- Local mode from lcd-ctrl.


#######################
## [2.0.0] - 13/10/2020
### Added
- Gate feature.
- OSC expander ON/OFF;
- Cell 57 to enable/disable of EPICS at startup;
- Forced MREBBOT command;
- Snapshots;
- Ordering and options code;
- NGPS 62.5-180;
- Interface PSM model selector (RESERVED);
- Auto generation of serial number (RESERVED).
- PSM and json exporter from report (RESERVED);
- Data usage, to enable it set the cell 58 (RESERVED);
- Agilent multichannels support during calibration (RESERVED);
- Limit min/max current output during calibration and check (RESERVED);
- NGPS-C10 200-50, NGPS-C10 350-25, NGPS 1000-10;
- Modbus TCP at port 502 (RESERVED);
- Cell 59 to enable/disable modbus TCP (RESERVED);
- Manuals;
- Remote IP debugger (RESERVED);
- GOTTY shell (RESERVED);
- Cell 54 to enable/disable dissipative support for FAST-PS-1K5;
- MFT and MFT:? command.

### Updated
- Yocto to Xilinx 2019.2 release;
- Recovery to 2.0.2;
- ssh keys;
- Web interface packages to 07/05/2020;
- Web interface theme;
- EPICS to 7.0.3.1;
- nodejs to 12.18.3;
- PSMs (RESERVED).

### Improved
- CPU usage;
- TCP/UDP Commands'rate.

### Optimized
- web interface for performance.

### Changed
- Reset of external DC power supply during crowbar test (RESERVED).
- Cables options for different models (RESERVED);
- Definition of tests and calibrations options (RESERVED);
- Console autocomplete shortcut from Alt to AltGr;
- Upgrade procedure from updt file;
- TRIG and WAVE command with gate feature.
- Report generation (RESERVED);
- Detailed help cell (enabled by default);
- Automatic reboot after firmware upgrade;
- When a report is exported, three files are saved html, psm and json (RESERVED);
- Unified capabilities between FAST-PS-1K5 and NGPS;
- WAVE command from WAVE:TRIGGER:POINT to WAVE:TRIGGER:POINTS and added WAVE:TRIGGER:GATE;
- NTP service;
- When the slew rate has changed from the web interface from section set point, this value is saved like default.

### Fixed
- MRAUX for FAST-PS-1K5;
- WAVE:N_PERIODS: and WAVE:POINTS: when in fault or off mode;
- Loop and upmode state after reboot in case of web interface;
- Network info on lcd-ctrl;
- Web interface height in case of 2K and 4K monitors;
- Web interface Firefox compatibility;
- MAC address at startup;
- lcd-ctrl crash when in local mode, under Control tab, in ON and a fault occured;
- cpid compatibility with old format;
- High CPU usage when upgrading firmware under particular settings;
- PSMs sync;
- Drop down menu scroll in the web interface;
- lcd-ctrl ERR message when in SFP mode;
- Temperature fault in case of parallel mode;
- Calibration set point EPSILON error (RESERVED);
- Calibation status when not available (RESERVED).


#######################
## [recovery 2.0.2] - 04/08/2020
### Fixed
- PSMs sync.


#######################
## [recovery 2.0.1] - 01/07/2020
### Fixed
- Partition table;
- Upgrade to sandard firmware without losing flash data.


#######################
## [1.5.30] - 27/02/2020
### Added
- Over current and over voltage;
- New firmware upgrade procedure for the next major update 2.0.0;
- Recovery image 2.0.0 (it is upgraded when the new upgrade procedure is started 1.5.30->2.0.0).


#######################
## [recovery 2.0.0] - 27/02/2020
### Added
- New firmware upgrade procedure for the next major update 2.0.0.


#######################
## [1.5.29] - 20/11/2019
### Changed
- Range of crowbar test (RESERVED).


#######################
## [1.5.28] - 07/11/2019
### Fixed
- Polarity inverter update time;
- NGPS in parallel mode.


#######################
## [1.5.27] - 05/11/2019
### Added
- Linear current generator to calibrate the current for monopolar models (RESERVED);
- Fast interface for FAST-PS-1K5 and NGPS.

### Fixed
- Web interface serial number visualization under Test and Calibration (RESERVED);
- Web interface slew rate visualization.

### Changed
- Web interface analog input calibration settling time (RESERVED).


#######################
## [1.5.26] - 14/10/2019
### Added
- Stop of calibration if clear event occurs (RESERVED);
- SFP readback for FAST-PS;
- OSC export (RESERVED);
- Capabilities selector under Test and Calibration (RESERVED).

### Fixed
- Web interface indicator bars around 0 for monopolar models.

### Changed
- Web interface scheduler to boost commands rate;
- AIN calibration with settling time (RESERVED).


#######################
## [1.5.25] - 04/10/2019
### Added
- Test and calibration section (RESERVED);
- Reports manager in web interface;
- TIMER command, it is stopped after the first fault with a resolution of 1ms. Can be reset with MRESET;
- Message fault description in web interface;
- Oscilloscope expander in web interface;
- PID selector in web interface;
- DHCP.

### Fixed
- Multiple messages when the web interface is reloaded from the same tab;
- lcd-ctrl error codes;
- Waveform stop value;
- Web interface disconnect event when the web browser is forced to be closed;
- IP memory optimization issue;
- Slew rates in PsParams for lcd-ctrl;
- UDP hangs out when commands are received in sequence in short time.

### Updated
- Web interface packages to 22/08/2019;
- node.js to 16.10.1;
- Report FAT revision to 1.3.0.

### Changed
- Minimum number of points for waveform from 100 to 5.

### Removed
- Cells 120, 121 and 122.


#######################
## [1.5.24] - 10/06/2019
### Updated
- Changed Duty cycle min/max limits on FAST-PS and FAST-PS-1K5 models.


#######################
## [1.5.23] - 17/06/2019
### Added
- FAST-PS 2516.

### Fixed
- Web interface wrong value of earth leakage current in some cases;
- TFT shift.

### Updated
- Components in the web interface from official repositories, on 17/06/2019.


#######################
## [1.5.22] - 05/06/2019
### Updated
- SFPEthernet diver with multicast IP address.


#######################
## [1.5.21] - 31/05/2019
### Fixed
- EPICS freezes due MLIMITS command.

### Added
- MPLIMITS.

### Removed
- MLIMITS power limits.


#######################
## [1.5.20] - 30/05/2019
### Added
- Debug mode;
- Oscilloscope;
- Web interface indicators about PID's limits;
- PID's architectures under web interface.

### Removed
- Parallel tab from lcd-ctrl in case of FAST-PS.

### Fixed
- Privileges for NTP and EPICS sections;
- Web interface PID's settings.

### Updated
- Web interface style;
- MLIMITS command with power limits.

### Note
- From this release all features of Visual_PS are ported to visual-js.


#######################
## [1.5.19] - 09/05/2019
### Fixed
- Temperature faults for the following modules
    FAST-PS-1K5     30-50
    FAST-PS-1K5     15-100
    FAST-PS-1K5     10-100
    FAST-PS-1K5     1-15


#######################
## [1.5.18] - 30/04/2019
### Removed
- visual-js web browser cache to be notified about updates.

### Updated
- Compatibility with Device Manager 1.1.4.

### Fixed
- Visualization of faults in case of a parallel system;
- Real time visualitazion faults;
- Overpower in case of parallel mode;
- Wait For OFF when there is not any load;
- Fixed update time of polarity inverter state machine.


#######################
## [1.5.17] - 12/04/2019
### Added
- FFT magnitude and phase spectrums;
- NTP sync and commands.

### Changed
- Password reset.

### Fixed
- Frequency and period validators for waveform editor;
- Oscilloscope freezes when web interface is not disconnected properly.


#######################
## [1.5.16] - 04/04/2019
### Removed
- SETDUTYMODE.

### Changed
- Quench is disabled when in ramp or waveform mode;


#######################
## [1.5.15] - 28/03/2019
### Added
- MLCMDS, MRGD commands;
- visual-js web application to replace Visual_PS;
- Wait for OFF;
- UDP server on port 10001;
- Socket.IO on port 10002;
- #NAK:37. UDP buffer overflow;
- #NAK:38. WAIT FOR OFF;
- Cell 56 to enable/disable detailed help.

### Changed
- #NAK contains description of error;
- EPICS restore/save commands do not restart ioc if EPICS:RESTART is not called;
- PASSWORD command accepts also USER level password;
- Polarity inverter does not set the magnetic relay if set point is 0;
- Overpower also with negative power.

### Fixed
- #NAK:21;
- lcd crash issue, black screen.


#######################
## [1.5.14] - 08/03/2019
### Fixed
- Default gateway.


#######################
## [1.5.13] - 14/02/2019
### Fixed
- NGPS 600-20 current calibration offset.


#######################
## [1.5.12] - 20/12/2018
### Added
- NGPS 600-20.

### Fixed
- Set float mode at startup.


#######################
## [1.5.11] - 18/12/2018
### Changed
- FF to SUPER-ADMIN.


#######################
## [1.5.10] - 11/12/2018
### Added
- New SFP IPs for FAST-PS;
- MRD command;
- NGPS 250-30, NGPS 300-30;
- SETPSW and RESETPSW commands.

### Changed
- lcd-ctrl's Control tab is enabled also when AIN mode is selected;
- PMODE command can be used only with ADMIN/SUPER-ADMIN user;
- Cell 35, from 40 to 50 and 60 to 69 are protected by ADMIN privileges.

### Fixed
- SETFLOAT mode command;
- lcd-ctrl's set point value when user closes the tab;
- EPICS'commands parser;
- EPICS ON/OFF status when it is changed by remote MON/MOFF commands (after the upgrade, it is necessary to restore db config).


#######################
## [1.5.9] - 12/11/2018
### Fixed
- Oscilloscope socket notifier.


#######################
## [1.5.8] - 10/11/2018
### Fixed
- Oscilloscope freeze;
- lcd-ctrl freeze when psm is empty.


#######################
## [1.5.7] - 09/11/2018
### Fixed
- MSIG, MSIGPU and PASSWORD commands.


#######################
## [1.5.6] - 08/11/2018
### Changed
- MASTER sync time at startup;
- Regulation fault;
- Commands'parser;
- SLAVE can exit only if link with master is OFF.

### Added
- Set point screen to lcd.

### Removed
- Graphs from lcd.

### Fixed
- Slaves'open loop current balancing;
- Fan control in case of slave;
- Feed forward startup in case of slave;
- High CPU usage;
- lcd-ctrl control tab when it is not in NORMAL mode.


#######################
## [1.5.5] - 24/10/2018
### Added
- Cell 55 to force remote OFF.

### Fixed
- ADC sync for FAST-PS.


#######################
## [1.5.4] - 22/10/2018
### Fixed
- Fan control for all FAST-PS.


#######################
## [1.5.3] - 22/10/2018
### Fixed
- Network connection in case of an ethernet switch 10/100Mb;
- LCD display shift.


#######################
## [1.5.2] - 18/10/2018
### Fixed
- Legacy status reg.;


#######################
## [1.5.1] - 17/10/2018
### Fixed
- Network issue with slow ethernet switch;
- FAST-PS1K5 temperature fault.


#######################
## [1.5.0] - 16/10/2018
### Added
- Oscilloscope (RESTRICTED);
- One firmware for all models;
- Parallel mode (NGPS and FAST-PS1K5);
- MREBOOT command;
- HWInfo driver;
- New faults registers (general, master, slave0, slave1, slave2);
- MFT command;
- Check AUX2 min threshold with AUXALARM in capabilities for NGPS.

### Fixed
- Waveform stop when module is in OFF;
- Interlock faults status when disabled manually;
- Font fault screen on lcd;
- Freeze when there are many concurrent connections;
- EPICS check files at startup;
- Loading screen;
- Model name on MASTER when parallel mode is enabled;
- Startup files after firmware upgrade from < 1.5.0 (requires two reboots after the first upgrade);
- EPICS screen log;
- Ethernet MAC address at startup;
- PMODE command in case of SLAVE mode.

### Updated
- Mean module for all models;
- Limits when user performs upgrade from an old firmware release to 1.5.0 (cell 50 is != 2);
- u-boot-xlnx_2018.2 to hf;
- MGPC and MAUX commands only for NGPS;
- MAUX:1 and MAUX:2 commands only for FAST-PS1K5;
- lcd-ctrl real time set point;
- Temperature check.


#######################
## [1.4.16] - 05/10/2018
### Fixed
- FAST-PS1K5-C3 10-100 I regulation.


#######################
## [1.4.15] - 03/10/2018
### Added
- FAST-PS1K5-C2 01-15;
- FAST-PS1K5-C3 10-100.


#######################
## [1.4.14] - 28/09/2018
### Updated
- EPICS commands.


#######################
## [1.4.13] - 10/09/2018
### Fixed
- UPMODE command, the command stores the mode in cell 113.


#######################
## [1.4.12] - 28/07/2018
### Fixed
- AIN mode selection from  lcd.


#######################
## [1.4.11] - 03/07/2018
### Added
- NGPS-C6 100-100.


#######################
## [1.4.10] - 29/06/2018
### Added
- Feed forward (NGPS).

### Updated
- u-boot-xlnx to 2018.2.


#######################
## [1.4.9] - 14/06/2018
### Updated
- u-boot-xlnx to 2017.4 to support new MMC.
set_network_config

#######################
## [1.4.8] - 05/06/2018
### Fixed
- MWIR:? return string;
- MWI:? and MWV:? (return realtime setpoint);
- Loop mode when it is performed a firmware upgrade from an old release;
- Open loop mode at startup.


#######################
## [1.4.7] - 31/05/2018
### Updated
- FAST-PS-M 6V, 8V, 10V and 60A gains.

### Fixed
- DSP startup in case of FAST-PS-M;
- Duty limit for FAST-PS-M.


#######################
## [1.4.6] - 08/05/2018
### Added
- EPICS:RESTART command.

### Updated
- EPICS:DB and EPICS:PROTOCOLS do not require to restart the power supply to apply the changes.


#######################
## [1.4.5] - 04/05/2018
### Fixed
- VER command in case of FAST-PS 2040.


#######################
## [1.4.4] - 03/05/2018
### Updated
- EPICS commands.


#######################
## [1.4.3] - 26/04/2018
### Added
- msigpu management.

### Updated
- UPMODE can be changed at runtime.

### Fixed
- Triggers for waveform.


#######################
## [1.4.2] - 24/04/2018
### Added
- Fan control.

### Updated
- Mean module for NGPS.

### Fixed
- MWIR in case of polarity inverter;
- Gauss probe;
- Polarity inverter timing;
- Max waveform points;
- Trigger points in case of waveform.


#######################
## [1.4.1] - 22/03/2018
### Fixed
- NGPS waveform period consistency;
- Default min I/V values for monopolar model when the user performs an upgrade from firmware version < 1.4.0.
- Fixed initialization of update_mode;
- IP changes when module is ON.


#######################
## [1.4.0] - 20/03/2018
### Added
- Embedded EPICS;
- Waveform.

### Updated
- Trigger and TRIG command.

### Removed
- SFP;
- Parallel mode FAST-PS1K5.


#######################
## [1.3.8] - 19/04/2018
### Fixed
- Freeze at startup.


#######################
## [1.3.7] - 23/01/2018
### Fixed
- FAST-PS1K5 ADC instability.


#######################
## [1.3.6] - 23/01/2018
### Fixed
- Polarity inverter.


#######################
## [1.3.5] - 09/01/2018
### Added
- NGPS-C4 400-50;
- NGPS-C5 200-60.

### Fixed
- I instability on some FAST-PS1K5 models.


#######################
## [1.3.4] - 12/12/2017
### Added
- Qt 5.4.3.

### Reduced
- Size of firmware image.

### Fixed
- Freeze when user changes the IP address from lcd menu;
- Minor glitches in EPICS and dev-mngr-serv.


#######################
## [1.3.3] - 14/11/2017
### Fixed
- Earth fuse;
- TFT NGPS.


#######################
## [1.3.2] - 7/11/2017
### Added
- NGPS-C3.

### Updated
- Cell 50 and 70:
- Parallel mode init.

### Fixed
- Random freezes during loading;
- Faults.


#######################
## [1.3.1] - 19/10/2017
### Updated
- Hardware bounds for set point.


#######################
## [1.3.0] - 17/10/2017
### Added
- fast-ps 3030;
- LCD power saving (at the moment only for FAST-PS1K5).

### Removed
- All old waveform's commands.

### Fixed
- Startup of MASTER and SLAVE in case of parallel mode for FAST-PS1K5;
- Trigger freeze.


#######################
## [1.2.6] - 28/09/2017
### Fixed
- Polarity inverter freezes.


#######################
## [1.2.5] - 18/09/2017
### Updated
- POL command, it can be executed when in ON state for NGPS.

### Added
- MRA command for NGPS and FAST-PS1K5.


#######################
## [1.2.4] - 12/09/2017
### Updated
- MSIG and MSIGPU commands for FAST-PS1K5.


#######################
## [1.2.3] - 8/09/2017
### Fixed
- Master and slave status in lcd-ctrl.


#######################
## [1.2.2] - 29/08/2017
### Updated
- DSP firmware for FAST-PS1K5 and NGPS;
- Si5344 for NGPS.


#######################
## [1.2.1] - 3/08/2017
### Updated
- DSP firmware for NGPS;
- PCONNECTIONS command.

### Fixed
- EPICS limits.


#######################
## [1.2.0] - 31/07/2017
### Added
- Polarity inverter capability.

### Fixed
- Upgrade from old firmware;
- Controls under Config tab in lcd-ctrl.

- Upgrade from old firmware;

#######################
## [1.1.5] - 19/07/2017
### Added
- Fast PID mode (cell 50 for CC and cell 72 for CV);
- Initial support to Qt5;
- Initial support to EPICS.

### Fixed
- Bar position in lcd-ctrl.


#######################
## [1.1.4] - 6/07/2017
### Changed
- Help command;
- MLOCKLCD command.


#######################
## [1.1.3] - 19/06/2017
### Fixed
- NGPS lcd images;
- SPI memory address.

### Changed
- VER command checks if power supply is in parallel mode and sets proper string;
- When the power supply is set to SLAVE then LOCAL mode is enabled;
- Added new PID module with new parameters, require at least Visual_PS-1.0.36.

### Added
- New commands.


#######################
## [1.1.2] - 12/04/2017
### Fixed
- AIN gain.


#######################
## [1.1.1] - 11/04/2017
### Fixed
- AIN in case of parallel mode.


#######################
## [1.1.0] - 31/03/2017
### Added
- Trigger mode command (enabled only for FAST-PS). trgmode, trgmode:?, trgmode:on, trgmode:off;
- Parallel mode command (enabled only for FAST-PS-1K5). pmode, pmode:?, pmode:off, pmode:master, pmode:slave;
- Changelog command. changelog;
- Limits command. MLIMITS, MLIMITS:? return #MLIMITS:MIN_V:MAX_V:MIN_I:MAX_I;
- Parallel tab in lcd-ctrl (enabled only for FAST-PS-1K5);
- Unified release cycle for all devices.

### Changed
- Read set points directly from the PID's inputs;
- Disabled SPFInfo in lcd-ctrl.

### Fixed
- Limits of V and I in lcd-ctrl;
- Graphs of V and I in lcd-ctrl.


#######################
## [NGPS 1.0.06] - old
### Changed
- New PID version.


#######################
## [FAST-PS 1.0.14] - old
### Added
- Multicast HW.


#######################
## [FAST-PS-1K5 1.0.3] - old
### Added
- Custom version FAST-PS-1K5-C1 40-40.

#######################
## [2.0.0] - 20/01/2020
### Added
- Compatibility with firmware 2.xxx.


#######################
## [1.1.11] - 6/11/2018
### Fixed
- Autoscale;
- Zoom in out.


#######################
## [1.1.10] - 29/10/2018
### Fixed
- Sync.


#######################
## [1.1.9] - 26/10/2018
### Fixed
- Multiple acquisition.


#######################
## [1.1.8] - 16/10/2018
### Fixed
- Windows 7 compatibility.


#######################
## [1.1.7] - 10/09/2018
### Updated
- Qt 5.11.1;
- Qt installer framework 3.0.4.


#######################
## [1.1.6] - 27/03/2018
### Fixed
- Save to file when the file name contains spaces.


#######################
## [1.1.5] - 01/02/2018
### Fixed
- Zoom in.


#######################
## [1.1.4] - 17/01/2018
### Fixed
- Save to file from SD with CLRF.


#######################
## [1.1.3] - 02/01/2018
### Fixed
- Save to file from SD, one data per line;
- Random crash on save to file from SD;
- Freeze on zoom in after long running;
- Freeze when two CT-BOXes are connected and later phisically disconnected.


#######################
## [1.1.2] - 20/12/2017
### Fixed
- Autoscaling.


#######################
## [1.1.1] - 18/12/2017
### Fixed
- Crash when the application is closed and connected to a device;
- Crash when user clicks on Cancel button but it is not connected to a device;
- Controls'size on Windows.


#######################
## [1.1.0] - 12/12/2017
### Added
- Automatic updates from repository.

### Fixed
- Slowdown at startup on Windows;
- Freeze at startup on some Windows 10 configurations;
- Fonts and controls'size.

### Updates
- Qt-5.10.0;
- QtInstallerFramework-2.0.


#######################
## [1.0.21] - 5/10/2017
### Added
- Model 1200.

#######################
## [1.2.2] - 6/10/2020
### Fixed
- Removed continuous writes when programming TetrAMM/PreDAC/EnBOX.


#######################
## [1.2.1] - 17/12/2019
### Fixed
- Changeable/unchangeable options for config device dialog.


#######################
## [1.2.0] - 02/12/2019
### Added
- CDCU DC link voltage check before to upgrade the firmware.

### Fixed
- Change device configuration.


#######################
## [1.1.7] - 22/11/2019
### Added
- CDCU compatibility;
- Manual update of remote power supplies.


#######################
## [1.1.6] - 30/08/2019
### Added
- DHCP flag detaction.


#######################
## [1.1.5] - 07/05/2019
### Added
- Connect to power supply;
- Firmware upgrade for power supplies;
- Multiple firmware upgrade for power supplies (the power supplies should be in the same subnet of the host and with unique IP);
- CT BOX.


## [1.1.4] - 23/04/2019
### Updated
- Power Supply compatibility from firmware 1.5.18.


#######################
## [1.1.3] - 16/10/2018
### Fixed
- Windows 7 compatibility.


#######################
## [1.1.2] - 10/09/2018
### Updated
- Qt 5.11.1;
- Qt installer framework 3.0.4.


#######################
## [1.1.1] - 20/12/2017
### Fixed
- Autoscaling.


#######################
## [1.1.0] - 18/12/2017
### Added
- Automatic updates from repository.

### Fixed
- Slowdown at startup on Windows;
- Freeze at startup on some Windows 10 configurations;
- Fonts and controls'size.

### Updates
- Qt-5.10.0;
- QtInstallerFramework-2.0.


#######################
## [1.0.10] - 3/10/2017
### Added
- Changelog.

#######################
## [2.0.6] - xx/xx/2021
### Fixed
- New lcd-cntrl main page UI
- Some bugs fixed
- Added Output Current Fault condition
- Fixed oscilloscope trigger mode bug



#######################
## [2.0.5] - 30/07/2021
### Fixed
- New lcd-cntrl main page UI
- Some bugs fixed

#######################
## [2.0.4] - 26/07/2021
### Fixed
- Commands speed improvements
- Signal Status management improvements
- Improved some internal commands

#######################
## [2.0.3] - 30/06/2021
### Changed
- Trigger Off management restored as in Main Server v1
- Modified the position of the configuration file
- Updated Components management
- Minor fixes

#######################
## [2.0.2] - 19/06/2021
### Fixed
- Trigger type from web interface.

#######################
## [2.0.1] - 25/05/2021
### Updated
- Card "UPDATE"

### Added
- new PID images

#######################
## [2.0.0] - 06/04/2021
### Added
- First Release of Regulator Main Server v2.